2023 Crown Vic Rules

– Aftermarket coils are okay.

– AC Condenser may be removed; may run aftermarket transmission cooler.

B. RADIATOR – Must contain water only.

C. BATTERY – May remain in stock location or battery may be moved inside drivers compartment and must be securely mounted and covered.

D. FUEL KILL SWITCH – In rear of deck or behind drivers roll cage or kill all switch if battery is relocated.

E. EXHAUST – Muffler is NOT required. Exhaust is 2-1/2″ max. No X, H, or y pipes. Pipes must go beyond the driver area and exit to the side or rear. Catalytic converter may be replaced with pipe

F. TRANSMISSION – Must remain entirely stock.

G. REAR END – Must remain entirely stock. Gear only 2.73, 3.27, 3.55, 3.73, 4.10 ratios only.
No aftermarket lockers. You may weld the spider gears or use factory posi.

INTERIOR
A. ROLL CAGE – maximum of a 4-point cage with 1 ¾ .095 tubing with 4 curved door bars on the driver’s side and 4 curved door bars on the passenger side to be eligible to race figure 8’s. Straight bars can be used on the passenger side for oval racing only. Must have a foot bar under the driver’s feet that extends from bottom of left “A” post to bottom of right A post of roll cage to be eligible to race figure 8’s. Must have a bar centered over transmission tunnel that connects the foot bar to the dash bar, a centered bar from the dash bar to the halo over driver’s head and a centered bar from the halo to the hoop behind the driver’s seat to be eligible to race figure 8’s. Must have a bar that connects the left and right legs of the hoop behind the driver’s seat just above the driveshaft tunnel and another one welded at approximately half the distance from the top of driveshaft tunnel to the roof. The rear hoop behind the driver’s seat must have an “x” from top left corner of hoop to bottom right leg of hoop and from the top right corner of hoop to the bottom left leg of hoop to be eligible to race figure 8’s. Must have a diagonal bar from bottom right front A post leg of roll cage to the mid mounted bar behind driver’s seat bar that is to be welded at what would be the center of the “x” in the hoop behind driver’s seat to be eligible to race figure 8’s. Cage must be welded to the frame and not the floor pan. A driver’s door plate is recommended. No offset cages. All roll cages must be painted.

B. SEAT & BELTS – A racing seat is required along with a 5-point racing harness. Belts can be no older than 3 years past the clearly marked manufacturer dates on them.

C. WINDOW NET – A properly mounted window net is mandatory and must be used at all times on track.

D. STEERING COLUMN – Must remain stock. Adding of a quick disconnect steering wheel is allowed.

E. WINDSHIELD – Must remain stock or Lexan or metal screen (2 half inch bars in front of driver for protection if running screen) and strapped in place. All other glass must be removed. All mirrors must be removed.

F. DASH –All airbags in the entire car must be removed.
Effective 2023: Dash and inner AC box and controls may be removed. Instrument cluster must remain intact and must still be operable.
No aluminum or fabricated dash panels. OBD 2 port must remain intact and operational.

G. PEDALS – Must remain stock.

H. BALLAST – No adding of any weight to the entire car. Track can add weight to any competitor at any time

EXTERIOR
A. SUSPENSION – No altering of the suspension including sway bar links. No spacers of any kind. No air ride. No cutting, no heating, or no lowering of springs. Shocks and springs can only be replaced by same stock parts or OEM replacements. Front and rear springs must match coil for coil, free height, and wire diameter. (Can cut two 2” holes above rear shocks to access top shock nut).

B. CASTER & CAMBER – You may adjust as factory adjustments allow. May run aftermarket camber bolts (only Moog Pt#K100094 or other aftermarket equivalent manufacturer.) Camber 4 degrees max (zero tolerance).